Kontroler punjenja akumulatora podesivo 6-60V

Pogledajte i ostale moje oglase!

Svi oglasi sa slikama su dostupni! Robu saljem cim se vratim sa terena, danas, najkasnije ujutru. 

Porucivanje preko telefona 0601540033, sms-a, viber, sasomange poruka.

Kontroler koji regulise punjenje akumulatora.

Karakteristike:

Opseg rada od 6-60V (podesivo)

Struja punjenja do 20A (nije podesivo)

Dimenzije: 79x43mm

Kontroler sa LCD displejom je namenjen za punjunje sirokog spektra akumulatora i baterija

posto ima veoma precizno podesavanje voltaze, pocevsi od pracenja niskog napona u akumulatoru i aktiviranja punjenja kada napon padne ispod zadatog napona do gasenja punjenja takodje na zadatom parametu kako bi se izbeglo prepunjavanje akumulatora. Elektronika se moze koristiti u sistemima od 6-60v kao i nadogradnja na postojeci auto punjac sa trafoom.

Napon punjenja mora biti veci barem za nekoliko volti u odnosu na akumulator, ne moze se puniti akumulator od 24V sa punjacem od 12V. Kontroler sluzi samo da kontrolise napon punjenja i da iskljuci punjenje kada dostigne zadati napon, odnosno da ponovo pokrene punjenje kada napon padne ispod zadate vrednosti. Struju punjenja (A) ne regulise.

Robu saljem samo post expressom ili preporucenom posiljkom.

U slucaju da posta iz nekog razloga ne radi saljem Beks kurirskom sluzbom.

Sifra: 873

Pogledajte i ostale moje oglase!

Charging mode IN: By setting the upper limit voltage UP and the lower limit voltage dn; when the battery voltage is less than or equal to the lower limit voltage dn, the relay turns on and the charger starts charging the battery; when the battery voltage is more than or equal to the upper limit voltage UP, the relay disconnects to complete an automatic charging; when the relay turns on, IN flickers, indicating that it is charging. Discharging mode OUT: By setting the upper limit voltage UP and the lower limit voltage dn; when the battery voltage is greater than or equal to the upper limit voltage UP, the relay turns on and starts discharging; when the battery voltage is less than or equal to the lower limit voltage dn, the relay turns off and completes an automatic discharging function; when the relay turns on, the OUT flickers, indicating that it is discharging. Tip: This product is a simple voltage controller. It can turn on and off the output by relay. It only plays the role of switching, and can not change the voltage. Functional instruction: 1. Calculation of Voltage Percentage: Battery Voltage/(Upper Voltage-Lower Voltage) 2. Key function: UP: Short press display % and time, long press 5 seconds to switch mode; charging mode: IN, discharge mode: OUT. SET: Short press to check the parameters currently set; long press to enter the parameter setting interface, set UP: voltage upper limit, dn: voltage lower limit, OP: turn-on time, dOP: delay turn-on time (0-999 seconds), FOP: forced turn-on time (0-10 seconds) in discharge mode. DOWN: Turn off/on electric relay enable (emergency stop function) turn off, LCD display OFF, relay disconnect: long press to set the status of LCD backlight, L-P: OFF backlight constant brightness, ON: Backlight automatically extinguishes after 5-10 minutes; after extinguishing, press any keys to wake up. 3. Parameter Settings a. Enter the parameter setting interface by pressing the SET; b. After entering the parameter setting interface, switch the setting parameters by short pressing SET; c. After choosing parameters, it can be set by UP/DOWN key, supporting short press or long press. d. If you want to set other parameters, repeat steps b and c; e. After all parameters are set, long press SET to exit and save; 3.1 Charging/Discharging Time Control Function 1) When the time parameter OP is non-zero, start charging/discharging time control. 2) When the relay turns on a charge/discharge, the countdown begins; when it is completed, the relay is automatically disconnected to complete a charge/discharge process; if the time is completed, under the charging mode, the detection voltage is less than the lower limit voltage dn or in the discharge mode, the detection voltage is larger than the upper limit voltage UP, and the charging time control function is automatically turned off and flashes. Indicate H: ER reminds users that time parameter setting is unreasonable; press any key to stop flickering; 3) When the charging/discharging time control is not turned on, the product will record a complete time. When entering the time display interface, flashing shows the charging time, then exiting the time display interface or clearing the next time the charging is turned on (relay is turned on). 3.2 Automatic parameter detection: When the parameters are set and exit, if the lower voltage limit DN is larger than the upper voltage up, the system will flicker to display "ERR" as a reminder. 3.3 .  

Sifra: 873

Pogledajte i ostale moje oglase!